Our bestselling motorbike ramp, with a capacity of 300kg per ramp (600kg capacity across the pair). Dimensions of each ramp: 2200mm long x 230mm wide. Folded length 1100mm. Minimum wheel width required is 100mm.
Please note, these motorcycle ramps are unsuitable for single axle or tracked machinery or vehicles, also not suitable for caster wheels or solid wheels. These ramps are not suitable for industrial use or professional mowers, for this application please view our professional range.
Single
Length (mm)
2200
Width (mm)
230
Height (mm)
100
Min. Load Height (mm)
200
Max Load Height (mm)
666
Weight per Ramp (kg)
7.5
Weight Per Pair (kg)
15
Capacity (kg)
300
Pair
Length (mm)
2200
Width (mm)
230
Min. Load Height (mm)
200
Height (mm)
100
Min. Load Height (mm)
200
Max Load Height (mm)
666
Weight per Ramp (kg)
7.5
Capacity (kg)
600
Ramp Capacity, Length & Load Height
This guide should help you gauge how long a ramp you require, so if you're in any doubt read the details below. If you still have questions after reading, feel free to give us a call. The crucial thing to know is your load height.
Load Height: this is the vertical measurement from the ground to where you rest the ramp onto.
Guide to the maximum load height is shown in the product description/table, please note the minimum Load Height will be 5% below the maximum height stated on the ramp, to calculate use (maximum load height - 5% = minimum load height).
For vehicle ramps EU guidelines recommend that no ramps with a gradient greater than 30% or 1:3.3 should be used. Essentially the load heightx 3.3,gives you your ramp length. Furthermore no TUV Certified Ramp is designed to exceed this gradient. Going over this gradient is can cause accident, injury or death and may invalidate the warranty.
Please check the wheelbase measurement of the machine you are loading is suitable for the capacity the ramp can take based on the wheelbase measurement advised. To check your wheelbase, look at the vehicle from side view, the distance between the centre of front wheel and rear wheel (rim centre) is your wheelbase.
For machines with an unbalanced weight distribution such as, scissors lifts, paving machinery, steel tracked machinery and machines with low ground clearance we would advise you contact us first, so we can check and advise on the most suitable solution.
For loading cars and other vehicles with either a) Low ground clearance b) Front and/or Rear overhang a gentler gradient is recommended (this will vary depending upon the vehicle). Please also note that most forklifts and pallet trucks are not built to be used on slopes. Please check the manual for the gradient information.
Further information can be seen in this blog article here
Designed for loading motorbikes, quad bikes and ATVs up heights of up to 666mm. Each ramp is 2200mm x 230mm x 7.5kg.
Folding motorcycle ramp, folds to half the length for easy to transport and store
300kg capacity per ramp, use as a single ramp to load motorbikes and mopeds or use as a pair to load quad bikes, ATVs and ride-on-lawnmowers (600kg capacity across the pair)
Smooth entry onto the ramp due to the angled foot
Safety straps areprovided to allow the ramp to be secured to the vehicle during loading
Lightweight aluminiumat only 7.5kg per ramp
No installation required, simply rest the aluminium loading ramps onto your van, trailer or steps and start loading
Slightly curved motorcycle loading ramps for improved ground clearance
Anti-slip surface with cut out grooves to allow dirt to drop through the ramps
Robot welded to ensure a solid, strong and durable construction
The maximum load height (vertical height from the ground to where the ramp will rest) is 666mm, for higher heights please view our 2.7m loading ramps
For higher capacities, we suggest viewing our folding loading ramps with support legs which offer capacities up to 680kg per ramp, 1360kg across the pair
Please note, these ramps are unsuitable for single axle or tracked machinery or vehicles, also not suitable for caster wheels or solid wheels. Not designed for plant machinery including tractors, diggers and similar items. These Ramps are not suitable for industrial use or professional use, for this application please view our professional range.
All pictures shown are for illustration purpose only. Actual product may vary due to product enhancement
Load quad bikes into your van or trailer with The Ramp People's folding aluminium loading ramp. Lightweight for easy storage and transportation. Capacities up to 1360kg across the ...
Easily find the right motorcycle ramp to load your bike into your vehicle or overcome steps. Consider your load height and the weight you wish to load. Our range includes folding, lightweight solutions. Various widths and capacities available to meet your requirements. ...